We have found that targeting an A/F ratio around lb of air per lb of fuel is best. For some pulverizer types, such as ball tube mills and highspeed attrition mills, often a A/F ratio is ...
mill performance identification methods no load run clean air flow test dirty pitot tube test mill fineness sampling trending of coal pipe metal temperature. ... clean air flow balance is computed between coal pipes deviation of + 2% indicates a satisfactory flow balance and further trending is required. may 24, 2012.
• Coal delivered to all coal pipes should be balanced • Coal flow, dirty air clean air flow should be balanced within permitted rage of deviation. MILL PERFORMANCE PARAMETERS ... 1/2 = m / s Dirty Air Flow = * * * 3600 / 1000 = T/hr A typical summary sheet of dirty pitot test report. MILL 6A ...
Make final trim adjustment in this position as advised after inspection of operating condition. Provide a flow path for the cold air and hot air from the PA fans to the mills. Make sure the mill discharge gates for test mill to be separately are open and the burner shutoff gates are open at coal burners for the test mill. Start mill ...
For a dust collection system to function adequately engineers must design and operate the system to maintain the (4) key design parameters of airflow (measured in CFM), airflow velocity (measured in FPM), Static Pressure/Static Resistance and Air to Cloth Ratio (or A/C). Changes to any of these key system parameters will result in systemwide ...
Each coal sampling kit we sell comes with everything you need to draw a proper isokinetic sample from a fuel line and conduct a comprehensive pulverizer test for optimum performance. With this kit, you will be able to perform clean air tests on each pulverizer as well as determine the static pressure and temperature, dirty air velocity, and ...
Coal Mill Air to fuel ratios are higher during: Startup. Shutdown. Interruptions in raw coal feed. ... Mill air flow is held constant at 140,000 Lbs./Hr. at coal flows <78,000 Lbs./Hr. to maintain minimum burner line of 3,500 Fpm. 2013 Annual Meeting | :
COALGEN 2005 August 17, 2005 San Antonio, Texas EPRI Coal Flow Loop (cont.) Precise Control Measurement of Air and Coal < % air flow measurement < % coal flow measurement 10120 ft/sec inpipe Velocity CFM 1 to 4 Air/Coal Ratio 2,00020,000 lbm/hr coal flow Ambient to 180 °F Air/Coal Temperature
Insert the coal sampling probe into the dustless connector, open the ball valve and push the probe all. the way until it hits the back wall of the burner line. Using a paint marker make a small mark on the. probe at the very end of the dustless connector. 4. Reverse Step 2 above and take the probe back out of the pipe.
The ASME PTC Coal Sampling System is utilized to sample particulate carried within an air stream. The sample is extracted isokinetically to determine the particulate flow rate. The sampling probe features a single, slotted nozzle meeting the geometry specifications of the ASME method. The probe is inserted into the flow stream and ...
Dirty Air Pitot Test System Details and Specifications ... DIRTY AIR PITOT TUBE (DAP) " or 2" NPT DUSTLESS CONNECTOR (DCDAP) . DAP UMBILICAL (DAPUMB) 10ft [3m] PROBE END WITH: HANDLE BUBBLE LEVEL (PBL) PRESSURE TUBESTHERMOCOUPLE PLUG COMBINED PRESSURE
Fan Performance... • Total pressure • Total pressure is the sum of the static and velocity pressure. Velocity pressure and static pressure can change as the air flows though different size ducts accelerating and de accelerating the velocity. The total pressure stays constant, changing only with friction losses.
To avoid hot air coming in direct contact with the hub and heating hub shaft, which in turn will transfer heat to the planetary gear box, upper and lower skirts are fixed on the hub forming a hollow chamber to be pressurized with cold seal air supplied through seal air pipe provided below bottom liners of the mill. To sweep the spilling coal ...
Temperature Of Coal Air Mixture At Mill Outlet ... Dirty air flow distribution should be within +/ 5% Coal distribution within +/ 10% of the mean value 56 Fuel line balance . 57 Clean Air Flow Test • Clean Air flowing through the fuel lines at normal operating temp and pres.
A dirty air probe is required when measuring flow velocity in an operating coal pipe. The dirty air velocities of each pipe should be within 5% of the mean of all the coal pipes to achieve uniform ...
4. Lower air flow results in better fineness less erosion. 5. Lower air flow can result in more pyrites, but fewer burner eyebrows. 6. Lower air flow means and a greater tendency to plug with wet coal. 7. Lower air flow leaves more reserve fines in the pulverizer. 8. Also note that lower air flow leaves a deeper bed depth of coal, and thus a ...
Also more amount of hot air will be needed to maintain the mill outlet temperature. Also there are likely chances of accumulation of coal as agglomerate and leads to mill choking. Every 1% increase in moisture in coal decreases the Boiler Efficiency by % Effect of Moisture on Mill Capacity Temperature of CoalAir Mixture at Mill Outlet ...
the results of air flow distribution at 4 corners of respective pulverizer. The Average Dirty air flow of 4 corners is TPH. With ±5% limit of TPH the air flow should be in the range of TPH to TPH. The dirty air was balanced at all the 4 corners. Coal Fineness Analysis:
The first test conducted by a testing crew is the dirty air traverse. That test uses the same sampling points when measuring velocities in the pipes. By measuring the true velocity flowing through the pipe, guessing an unknown velocity, as required by the ASME test procedure, is eliminated. After the dirty air velocity test is completed, the ...
In fact, using the "seal air off" coal piping flow numbers in Table 2 would lead to a very inaccurate calibration: Actual PA flows would be up to times higher than the reading of the flow ...
© DZCrusher - كل الحقوق محفوظة
